Clover Electronics CDR0850 Bedienungsanleitung

Contents 1 INSTRUCTION MANUAL Stand-Alone 8 Channel DIGITAL VIDEO RECORDER MODEL CDR0850 Copyright © 2007 Clover Electronics U.S.A. All

Stand-alone DVR Instruction Manual 10

Stand-alone DVR Instruction Manual 7-6.2. All Manual / Timer recording button ▫ Click the All Manual / Timer recording button in the RECORD menu and

7. Setup 7-6.3. All Motion ON / OFF, Sensitivity and Velocity Setting ▫ Click the button in the RECORD menu and the ALL MOTION setup pop-up window

Stand-alone DVR Instruction Manual 7-6.4. All Sensors ON / OFF ▫ Click the button in the RECORD menu and the ALL SENSOR setup pop-up window will b

7. Setup 7-6.6. Recording Speed ▫ Click the F/S (Frames Per Seconds: Recording Speed) button on each of the channels in the RECORD menu and the Reco

Stand-alone DVR Instruction Manual 30 25 15 12 10 8 7 6 5 5 3 3 2 2 1 1 NTSC OFF PAL OFF [Fig.7-67 Recording Speed for each channel] 7

7. Setup 7-6.8. Recording Mode The factory default setting for Recording is the Manual Recording (or called Continuous Recording), which keeps record

Stand-alone DVR Instruction Manual 7-6.9. Recording by Motion Detection When the menu of motion properly setup (See section 7-6.3 on page 101 for

7. Setup ▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Motion or Sensor activation. Click the mouse on the PRE in the

Stand-alone DVR Instruction Manual ▫ Spot Setup If the “ON” is selected by clicking the mouse on the SPOT button in the MOTION menu, a full screen

7. Setup - All Clear Click the ALL CLEAR button in the MOTION menu in order to clear the Motion Detection Area, and the window turns to white color

1 Unpacking Care should be taken when unpacking to avoid damaging the unit. Please check that the following items are included: ▶ Stand-al

Stand-alone DVR Instruction Manual By Window Set Click the WINDOW SET button in the MOTION menu on each of the cameras and click one of cells (330 c

7. Setup - Window Clear Click the WINDOW CLEAR button in the MOTION menu in order to clear the Motion Detection Area, and the window you already crea

Stand-alone DVR Instruction Manual By Each Cell Click the EACH CELL button in the MOTION menu on each of the cameras and click the mouse on each of

7. Setup ▫ Map View Click the MAP VIEW button in the MOTION menu to view the current settings for Motion detection area. Right-click on the curr

Stand-alone DVR Instruction Manual 7-6.10. Recording by Sensor (PIR Sensor) ▫ Click the mouse on the button for each of the channels in the RE

7. Setup ▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Sensor activation. Click the mouse on the PRE in the SENSOR menu

Stand-alone DVR Instruction Manual ▫ Alarm Hold Time Setup The system continues recording for the Alarm HOLD TIME and finishes the recording. Clic

7. Setup 7-7. NETWORK ▫ Click the “NETWORK” button in the SETUP menu and the NETWORK menu will be displayed on the screen as shown in Fig.7-94.

Stand-alone DVR Instruction Manual [Fig.7-95 IP Mode button] [Fig.7-96 IP Mode pop-up window] 7-7.2. GATEWAY, SUBNET, IP ADDRESS ▫ Click t

7. Setup 7-7.3. Port ▫ PORT is the TCP address of the program, which is used to connect to the network viewer. It can be set from 1 to 65535 values

Stand-alone DVR Instruction Manual Stand-alone DVR (Digital Video Recorder) Unit CDR0850 is the most reliable and functional embedded DVR system

Stand-alone DVR Instruction Manual 7-7.4. MAC ID ▫ MAC ID is connecting address for Ethernet, every unit has 12 digit address (HEX 6 byte). MAC ID

7. Setup ▫ IP ADDRESS / PORT DO NOT CHANGE THE IP ADDRESS AND PORT NUMBER IN THE MNS MENU IF YOU DON’T HAVE ANY SPECIAL SERVER TO ACCESS YOUR DVR WI

Stand-alone DVR Instruction Manual 7-7.6. DDNS (DYNAMIC DOMAIN NAME SYSTEM) ▫ Select the DDNS button in the NETWORK menu by clicking the mouse, pre

7. Setup - alues, click on the OK button. ▫ USER ID USER ID in the DDNS menu and enter the USER ID that is registered to the - ▫ PASSWORD SSWORD

Stand-alone DVR Instruction Manual 7-7.7.2. Registration to the DDNS server Visit at www.dyndns.org to register. Registration to DYNDNS.ORG 1. Visi

7. Setup 7-8. VIDEO ENHANCE ▫ Click the VIDEO ENHANCE button in the SETUP menu to enhance the picture quality on each of channels and VGA OUTPUT suc

Stand-alone DVR Instruction Manual 7-8.1. VIDEO ENHANCEMENT ON EACH CAMERA ▫ Click on an INPUT button in the VIDEO ENHANCE menu. ▫ The CONTRAST an

7. Setup 7-8.2. VIDEO ENHANCEMENT ON VGA OUTPUT ▫ Click on the VGA OUTPUT in the VIDEO ENHANCE menu. ▫ The CONTRAST, BRIGHTNESS and SATURATION slide

Stand-alone DVR Instruction Manual 128

129 8 Remote Host Program CONTENTS 8-1. REMOTE PROGRAM OVERVIEW...

Features ▶ Multi Functional Record -Powerful, multiple Record Modes available: Manual (Continuous), Timer, and Motion Detection Recording. ▶ Us

Stand-alone DVR Instruction Manual 8-1. Remote Program Overview The Remote Host Program allows you to view live video, search archived video,

8. Remote Host Program 8-2. Installing the Program to PC Install the program into PC by using program CD (supplied) as follows. How to install the p

Stand-alone DVR Instruction Manual 8-3. Internet Explorer When you are trying to use this function, it is highly recommended that the password sho

8. Remote Host Program • Click on the click here on the following message. This site wants to install the following add-on: ‘SmViewer’ from ‘Clover E

Stand-alone DVR Instruction Manual 8-4. Remote Host ④ ⑥ ⑤ ③ ② ① [Fig.8-5 SmViewer] 134Buttons of Remote Host Program

8. Remote Host Program 8-4.1. Setup ① ② ③ ④ [Fig.8-6 HOST CONFIG window] ① Version number It represents the current version number of the

Stand-alone DVR Instruction Manual ③ Network Image ▫ Size Choose a Size (Resolution) among D1, Half D1 and CIF you wish to display on the SmView

8. Remote Host Program 8-4.2. Connection There are two ways to access the DVR through the SmViewer as follows. ▫ With Set Direct setting - Click th

Stand-alone DVR Instruction Manual 8-4.3. Switch the Normal Screen to Full Screen ▫ Click the “FULL SCREEN” button on the SmViewer and the curre

8. Remote Host Program 8-4.4. Speaker / Microphone ⑤ ④ ① ② ③ [Fig.8-10 Speaker / Microphone] Buttons of Remote Host Program ① Audio Input chann

Stand-alone DVR Instruction Manual 14

Stand-alone DVR Instruction Manual 8-4.5. Copy There are four icons such as NETWORK, USB, CD and DVD in the COPY menu of the SmViewer. The recorded

8. Remote Host Program [Fig.8-12 Copying on the SmViwer] [Fig.8-13 Copy Completion] 141

Stand-alone DVR Instruction Manual 8-5. PLAYER [Fig.8-14 Player] ⑦ ⑧ ⑩⑪⑫ ③ ④ ⑤ ⑥ ② ① ⑨ Chart. Button of Player Program ①

8. Remote Host Program ① Status window (Play mode, Date, Time) It indicates the play mode, date and time. [Fig.8-15 Status window] ② Calen

Stand-alone DVR Instruction Manual [Fig.8-17 Convert AVI window] [Fig.8-18 Backup Files by Networking] [Fig.8-19 DvrRecData by USB]

8. Remote Host Program [Fig.8-20 Select one of the Channels] [Fig.8-21 Start Convert Button] How to play the AVI files

Stand-alone DVR Instruction Manual ④ Search button for Replaying - Click the Search button on the Player and the Browse for Folder will be dis

8. Remote Host Program 147 [Fig.8-22 Print command window] [Fig.8-23 Print image] ⑦ Division button Select one of the following

Stand-alone DVR Instruction Manual ⑨ Search slider for replaying The slider can be moved left and right by clicking the slider on the bar and dr

9 Installation of additional HDDs CONTENTS 9-1. HDD (HARD DISK DRIVE) INSTALLATION...

3 What to do at the time of Installation Stand-alone DVR should be installed in the following order; 1. Make sure all the required hardware is

Stand-alone DVR Instruction Manual 9-1. HDD (Hard Disk Drive) INSTALLATION ▶ Three of internal Hard Disk Drives (HDD) and a CD R/W or DVD R/W ca

9. Installation of additional HDDs 9-2. Installation of an additional HDD ▶ Set the jumper setting to “Cable Select” position on the additional H

Stand-alone DVR Instruction Manual 152

APPENDIX CONTENTS RECORDING TIME TABLE ...

Stand-alone DVR Instruction Manual Recording time table HDD: 300GB Recording Resolution: Half D1 (720 x 240) Based on 8 cameras

Factory default settings (1) LIVE SCREEN 8 SPLIT OSD ON (2) TIME / DATE DISPLAY : ON TIME FORMAT : 24 HOUR DATE FORMAT : YYYY/MM/DD (3)

Stand-alone DVR Instruction Manual (8) AUDIO AUDIO 1 : RELATED CAMERA CH 1, RECORD OFF, MIC 5 AUDIO 2 : RELATED CAMERA CH 2, RECORD OFF, MIC 5 AUDI

(10) NETWORK TYPE : DYNAMIC PORT : 113 SERVER 1 MODE : DISABLE SERVER 1 IP ADDRESS : 65.60.84.25 SERVER 1 PORT : 300 SERVER 2 MODE : DISABLE SERVER

Stand-alone DVR Instruction Manual 158

FAQ CONTENTS I CANNOT LOGIN ...

Stand-alone DVR Instruction Manual 16

Stand-alone DVR Instruction Manual I cannot login ▶ Please check if the link LED of DVR and LAN port of PC are lit. ▶ Please check if the IP ad

Limited 2Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from sta

Stand-alone DVR Instruction Manual How to obtain Factory Service z Original purchaser must fill out the warranty card and mail it to the factory w

4 Specifications ITEM Television System NTSC PALRefresh Rate 60 fields/sec 50 fields/secVideo Resolution 720x480 720x576Video

Stand-alone DVR Instruction Manual 18

5 Installation CONTENTS 5-1. CONTROLS AND CONNECTORS (FOR 8CH & 16CH DVR)...2

2

Stand-alone DVR Instruction Manual 5-1. Controls and Connectors (For 8Ch & 16Ch DVR) z Front [Fig 5-1. Front View] JOGSHUTTLEHDD

5. Installation - B a. Display (Full / Split) b. Emergency Record c. Zoom d. Quick Replay e. OSD On/Off f. Audio g. Stop (ESC) h. PTZ

Stand-alone DVR Instruction Manual 5-2. Note for Installation  Install the system according to the instructions described in this manual.  T

5. Installation 5-3. System Connection [Fig 5-3. System Connection] 23

Stand-alone DVR Instruction Manual 5-4. Installation 5-4.1. Camera Connection ▫ Connection of Normal Cameras Connect the cameras to the Video

5. Installation ▫ VGA Monitor Connection Connect the VGA Monitor’s connector to the “DSUB 15 Pin Connector” on the rear of the unit. Output for VGA

Stand-alone DVR Instruction Manual - 5-4.3. Sensor Connection and RELAY IN &OUT ▫ SENSOR Connection (SENSOR IN) Connect the sensor to ALM

5. Installation 5-4.4. RS232C Connection ▫ Connect the cable to the “RS232C PORT” on the rear of the unit. Specification of the RS232C connector is

Stand-alone DVR Instruction Manual 5-4.5 Connection to an Ethernet (Optional) Network ▫ Connecting the cable to Ethernet. Our Ethernet connector

5. Installation 5-4.6. POWER CONNECTION Select proper voltage (see fig 5-12) and connect to a reliable power source. It should not be shared with

Contents CONTENTS ABOUT THIS MANUAL ...

Stand-alone DVR Instruction Manual 30

6 How to operate CONTENTS 6-1. GENERAL INFORMATION ...

Stand-alone DVR Instruction Manual 32CONTENTS 6-7. LIVE...

6. How to Operate 6-1. General Information ▫ You can operate all functions of the system by use of the 28 buttons located on the front panel, remot

Stand-alone DVR Instruction Manual 6-2. Operating Interface There are 3 ways to operate the system by pressing the buttons on the front panel or

6. How to Operate 6-3. IR Remote Controller 1. Record 2. Power On/Off 3. Display format (Split) 4. System status 5. Pan / Tilt 6.

Stand-alone DVR Instruction Manual 6-4. Power On/Off 6-4.1. POWER ON On the front panel or the remote controller: Press the POWER button on the fr

6. How to Operate 6-4.3. APPEARANCE OR DISAPPEARANCE OF POWER BUTTON The Power On/Off button and the Audio buttons (See 6-7.4) as shown in Fig.6-3-1

Stand-alone DVR Instruction Manual 6-5. Menu Bar On/Off Right-click on the screen in the LIVE or the RECORD mode and the MENU bar will be appear

6. How to Operate 6-6. Display Screen 6-6.1. FULL SCREEN [Fig.6-5 FULL screen] CAMERAAUDIOCOPYCURRENTRECORDSEQUENCE 39

Stand-alone DVR Instruction Manual 6-6.2. SPLIT SCREENS...

Stand-alone DVR Instruction Manual 6-6.2. SPLIT SCREENS FULL SCREEN SEQUENCING SCREEN [4B] 2nd QUAD SCREEN [4A] 1st QUA

6. How to Operate 6-7. LIVE 6-7.1. FULL SCREEN ▫ Full SCREEN is available in the LIVE mode or the RECORD mode. ▫ Click on a certain camera’s scr

Stand-alone DVR Instruction Manual 6-7.3. SEQUENCING SCREENS ▫ Displaying the cameras in SEQUENCE is available in the LIVE mode or the RECORD mode

6. How to Operate 6-7.4. LIVE AUDIO ▫ If cameras (up to 4 cameras) have audio function, it will sound in the live mode. ▫ Click the CHANNEL button

Stand-alone DVR Instruction Manual 6-7.5. ZOOM The image on the screen will be zoomed up to 2 times when the ZOOM button is clicked in the LIVE mod

6. How to Operate 6-7.6. OSD ON / OFF OSD ON /OFF is possible in the LIVE mode or RECORD mode. ▫ Click the OSD button on the MENU bar to turn the OS

Stand-alone DVR Instruction Manual 6-7.7. PAN / TILT ▫ Click the PAN/TILT button on the MENU bar in the LIVE mode to access the PAN/TILT cameras.

6. How to Operate PAN / TILTCHANNELZOOM / FOCUS [Fig.6-15 PAN/TILT CONTROL window] ▫ Channel Selection and Screen Conversion To ch

Stand-alone DVR Instruction Manual 6-7.8. SYSTEM STATUS ▫ Click the SYSTEM STATUS button on the MENU bar to see the system status as shown below

6. How to Operate 6-7.9. POWER LOSS LISTS The list indicates the time/date when the system power is turned OFF. ▫ Click the POWER LOSS LISTS butto

Contents 7-2.1. TIME / DATE ...

Stand-alone DVR Instruction Manual ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm changes

6. How to Operate 51 6-7.10. VIDEO LOSS LIST The list indicates the video loss channel and the time/date when the video signal is disconnected. ▫ Cl

Stand-alone DVR Instruction Manual ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm changes.

6. How to Operate 6-8. Record This system provides Watchdog function. When power goes off during recording and the power turns on, the system will

Stand-alone DVR Instruction Manual The MOTION ( ) and SENSOR ( ) as shown in Fig.6-24 should be turned ON in this recording mode. ▫ Press the R

6. How to Operate 6-8.4. Timer Event Recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in the SETUP men

Stand-alone DVR Instruction Manual 6-8.5. Recording Icons The Recording Icons depends on recording modes are displayed on the upper left hand corne

6. How to Operate 6-9. REPLAY 6-9.1. QUICK REPLAY It is available only by pressing the PLAY button on the front panel or the QICK SEARCH button on

Stand-alone DVR Instruction Manual 6-9.2.1. Playback Devices In order to payback, plug the USB devices such as external USB HDD, USB memory to the U

6. How to Operate ▫ Select the hour on the Start Time Select Window (See Fig.6-32) by clicking the mouse on the Hour (0 – 23 hour) you wish to start

Stand-alone DVR Instruction Manual 7-6.8.2. Manual Event Recording...

Stand-alone DVR Instruction Manual 6-9.2.3. Replaying Replaying start time set-up can be possible within a recording time extent. ▫ Replay buttons

6. How to Operate ▫ How to control while replaying ③ ④ ② ④ ③ ⑤ ⑥ ① [Fig.6-35 Replay screen] ① Search Slider It is possible to play

Stand-alone DVR Instruction Manual the button to view the next frame in still image. ⑤ Speaker ON / OFF Turn speaker ON or OFF. ⑥ Speaker Vo

6. How to Operate - Click the mouse on one out of channels during replaying to view a full screen. - Click the mouse on the full screen during repl

Stand-alone DVR Instruction Manual 6-10. COPY ▫ Click the COPY icon on the MENU bar, and the COPY window as shown in Fig.6-38 will be displaye

6. How to Operate ▫ Connect the USB devices to the DVR ▫ Click the SETUP icon on the MENU bar, and the SETUP menu will be displayed. ▫ Click the DIS

Stand-alone DVR Instruction Manual [Fig.6-40 Copy Start time and Channel Selection window] ③channelselection②HOURselection button①Al

6. How to Operate [Fig.6-41 Copy Start/End setup buttons] By using the Start/End set-up bar: The starting time to copy can also be set by clicki

Stand-alone DVR Instruction Manual 6-10.4. Copying the recorded data during replaying The system, CDR0850 allows users to copy the recorded data

6. How to Operate [Fig.6-44 End Copy Time Setup window] ▫ Choose one among NETWORK, USB, CD and DVD which are ready to copy (See secti

Contents 9-2. INSTALLATION OF AN ADDITIONAL HDD... 151 APPENDIX...

Stand-alone DVR Instruction Manual DVD-RW COPY Save the recorded data on DVD-R/W Medias. Click the DVD-R/W button to start copy. ▫ As soon as o

7 SETUP CONTENTS 7-1. SETUP...

Stand-alone DVR Instruction Manual 72CONTENTS 7-4. CAMERA ...

7. Setup 73CONTENTS 7-7. NETWORK ...

Stand-alone DVR Instruction Manual 7-1. SETUP [Fig.7-1 Setup Icon on MENU bar] It is possible to set up the menus in the LIVE mode and partly i

7. Setup 7-2. SYSTEM ▫ Click the “SYSTEM” button in the SETUP menu, and the SYSTEM menu shown in Fig.7-3 will be displayed. ▫ Click the “EXIT” b

Stand-alone DVR Instruction Manual 7-2.1. TIME / DATE ▫ Click the “TIME/DATE” button in the SYSTEM menu, and the TIME/DATE menu will be displayed (

7. Setup ▫ DATE FORMAT There are three formats to display the time and date as follow. • MM / DD / YYYY: For U.S.A. • YYYY / MM / DD: For Asian coun

Stand-alone DVR Instruction Manual 7-2.2. SYSTEM CONFIG ▫ Click the “SYSTEM CONFIG” button in the SYSTEM menu, and the SYSTEM CONFIG menu will be d

7. Setup [Fig.7-12 Confirmation window of Factory Default] 7-2.2.2. LOAD CONFIG / BACKUP CONFIG You can save up to four different sett

Stand-alone DVR Instruction Manual 8

Stand-alone DVR Instruction Manual [Fig.7-14 LOAD CONFIG window] ▫ BACKUP CONFIG This function is to save the current settings to load t

7. Setup [Fig.7-16 BACKUP CONFIG window] 81

Stand-alone DVR Instruction Manual 7-2.3. PASSWORD ▫ ON/OFF Select ON or OFF by clicking the mouse. If the ON is selected, the password has to be

7. Setup 83 7-2.4. IR REMOTE ID Up to 16 DVR systems can be controlled by only one remote controller we provided, but IDs should be assigned on eac

Stand-alone DVR Instruction Manual 7-2.5. FIRMWARE UPDATE There are two ways to update the firmware through USB memory and the SmViewer (GUI). We re

7. Setup 7-3. DISK MANAGER ▫ Click the “DISK MANAGER” button in the SETUP menu and the DISK MANAGER window will be displayed (See Fig.7-22). ▫ Clic

Stand-alone DVR Instruction Manual 7-3.1. HDD WRITE FAIL If HDD is in full and the OVERWRITE on the HDD is turned OFF in the recording mode, the sy

7. Setup [Fig.7-25 HDD FORMAT window] 87

Stand-alone DVR Instruction Manual 7-4. CAMERA ▫ Click the “CAMERA” button in the SETUP menu and the CAMERA menu will be displayed (See Fig.7-26)

7. Setup 7-4.1. Camera ON/OFF ▫ Click on each of the channels to select the “O” or “X” in the CAMERA menu. If the “O” is selected, the corresponding

About this manual This is the Instruction Manual for Stand-alone type DVR model CDR0850. This Manual describes how to install and operate the

Stand-alone DVR Instruction Manual 7-4.3. Buzzer In order to alert users, the Buzzer will sound at that time video signal lost. ▫ Click on each

7. Setup 7-4.5. Pan/Tilt Settings ▫ Click the PAN/TILT button on the corresponding channels in the CAMERA menu and the PAN/TILT window will be displ

Stand-alone DVR Instruction Manual ▫ Pan/Tilt Vendor select Click the “PAN/TILT & REMOTE” button in the PAN/TILT window and the vendor lists

7. Setup ▫ Baud rate Click the “BAUD RATE” button in the PAN/TILT window and choose a value among 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 384

Stand-alone DVR Instruction Manual ▫ Stop Bits Click the “STOP BITS” button in the PAN/TILT window and select 1 or 2 on the Stop Bits pop-up window

7. Setup 7-4.6 Display ▫ Click the DISPLAY button in the CAMERA menu and select the ON or OFF. If the “ON” is selected, the camera name (camera tit

Stand-alone DVR Instruction Manual 7-5. AUDIO ▫ Click on the AUDIO button in the SETUP menu and the AUDIO menu will be displayed on the screen.

7. Setup 7-5.1. Camera Channel ▫ Click the Camera Channel button in the AUDIO menu and select up to 4 cameras among CAM 01 through CAM 08 which has

Stand-alone DVR Instruction Manual 7-5.3. Microphone Volume ▫ Adjust audio volume by clicking the ▲ or ▼ button. [Fig.7-53 Microphone Volume

7. Setup 7-6. RECORD ▫ Click the “RECORD” button in the SETUP menu and the RECORD menu will be displayed as shown in Fig.7-54. ▫ Click the (EXI